Equipment-manual-derived summary. This is the supplied English warehouse/handling summary, not a complete manufacturer Safety Data Sheet. Use alongside the original manufacturer document and product label. Source revision: Manual rev0; issue date not stated. Website/PDF edition: 11 October 2026, version 1. This is equipment safety information, not a chemical SDS. The full manufacturer manual and parts diagram are not included in the supplied summary.
Check the edition date before use. The PDF download and this page carry matching content; consult ECOPROCORK for the current manufacturer safety document.
Document title: English equipment-derived warehouse submission summary
Product name: CP19 Spray Gun
Manufacturer: DECOPROYEC
Source document basis: Instruction and Maintenance Manual – CP19, reference REF. 81 06 03 026 DECOPROYEC (rev0).
1. Product identification
Commercial product name: CP19
Product type: Professional spray gun for projected cork and similar coatings
Manufacturer: DECOPROYEC
Manufacturer address: C/ Trilladores nº47, Nave 4 y 5 (P.I. Los Molinos), C.P. 02520, Chinchilla de Montearagón, Albacete, Spain
Contact: +34 967 261787 / +34 616 897845
Email: de********@********ec.com
2. Intended applications
The manual states that the CP19 is intended for applications with:
projected cork
stippled-finish paints or “gotele”
textile coatings on medium-sized surfaces.
3. Technical characteristics
Nozzles: 6 mm standard, with 5 mm and 8 mm available as options
Body: anodized external treatment
Air consumption: 110 l/min at 2.5 bar and 125 l/min at 3 bar
Funnel capacity: 5 litres, nylon
Weight: 605 g
Air inlet: CR ¼
Supply system: gravity
Functioning: valve / continuous air.
4. Operating modes
The manual states that the gun can work in two different modes:
Valve mode
In this default factory setting, air only exits through the needle when the trigger is pulled.
Continuous air mode
In this mode, air exits continuously through the needle regardless of trigger position.
The manual gives instructions for switching between these two modes using a size 4 Allen key at the back of the needle assembly. It also warns that when setting continuous air mode, the cap must not be loosened so far that it protrudes the needle.
5. Working instructions
The manual says the size of the sprayed drop can be adjusted using the product regulator:
turning clockwise gives bigger drops
turning counterclockwise gives smaller drops
It also notes that the higher the product viscosity, the bigger the sprayed drops will be.
6. Cleaning and maintenance
The stated cleaning procedure is:
empty the product tank
fill with water or the appropriate solvent
spray until completely clean
dry the gun
grease wear points properly, including the needle, threads and trigger.
7. Safety instructions
The manual includes the following safety rules:
do not use the spray gun for operations for which it has not been designed
read all warnings on the products being used
use approved masks
do not aim the gun at people or animals
disconnect from the compressed air network before any repair
use the gun in a well-ventilated area where there is no risk of explosion or fire
never exceed 8 bar pressure
once work is finished, close the product regulator completely to prevent vaporisation.
8. Waste and environmental note
The manual states that packaging, disused equipment, tools, polluting products and any waste arising from activity should be taken to the appropriate waste sorting and treatment point.
9. Warranty summary
The manual states:
warranty applies only against manufacturing defect
validity period is 2 years from date of purchase
warranty covers repair in the manufacturer’s facilities or technical services
damage due to bumps, falls or similar causes is excluded.
10. Parts and service note
The manual includes an exploded view and parts listing for the CP19, including:
tank
clamp
nozzle nut and joint
nozzle options
trigger
packing nut
joint kit
regulator bushing
needle and needle screw
spring
air regulator
air inlet adaptors
trigger limiter
complete kit.
11. Warehouse handling note
For warehouse onboarding, the CP19 should be treated as a professional application tool, not as a chemical product. It should be recorded as:
equipment item
supplied with instruction and maintenance manual
requiring clean, dry storage
protected from impact damage
checked on receipt to confirm it matches the ordered specification
distributed with its operating and safety instructions.
12. Submission note
This text is an English equipment-derived warehouse summary prepared from the manufacturer’s CP19 Instruction and Maintenance Manual. It is suitable for UK warehousing, distribution onboarding and internal equipment handling review, and should sit alongside the original manufacturer manual, not replace it.