Generated from the current web datasheet.
Technical datasheet · ECOPROCORK®
Web edition 1.2 · Updated 19 October 2026 · Source: DS-Thermal-Paint-V1.pdf. No issue date is stated in the source sheet.
Product information from the existing shop datasheet, with clarification notes where source details are incomplete. Values are source reported; confirm the current product, grade and complete system specification before installation.
DECOCORK is described in the source as a flexible, cork-based paint available in different colours. The source describes resistance to microcracking and a contribution to insulation of the coated surface, without giving a conductivity, R-value or whole-wall performance result.
Mix thoroughly before use. The source specifies brush or airless-spray application and recommends at least three coats over the complete surface, allowing each coat to dry before the next.
Substrate preparation, primer, operating pressure, nozzle, application temperature and storage conditions are not specified in the attached sheet. Obtain current instructions for the project and equipment setup.
Source-reported values and test references. Underlying test reports have not been verified for this web edition.
| Property | Source-reported value | Reference or note |
|---|---|---|
| Density | 1.25 g/cm³ | UNE-EN ISO 2811-1 |
| Non-volatile matter | 52.00%; after 1 hour at 125°C | UNE-EN ISO 3251 |
| Non-volatile matter by volume | 40.20% | UNE-EN ISO 3233-3 |
| Touch dry | 30 minutes; 95 µm dry film | UNE 48301 |
| Total drying | 1 hour 35 minutes; 95 µm dry film | UNE 48301 |
| Theoretical consumption | 0.25 kg/m² at >80 µm; 0.31 kg/m² at >100 µm | Source notation |
| Theoretical area coverage | 5.0 m²/L at >80 µm; 4.0 m²/L at >100 µm | Source notation |
| pH | 9 ± 0.5 | Source sheet |
| Recommended coats | At least 3, allowing drying between coats | Source narrative |
The source does not say whether the stated theoretical figures apply per coat or to a completed three-coat build-up. Confirm the required dry-film thickness and total consumption with the manufacturer.
Drying-test conditions beyond the stated film thickness are not supplied. Allow for actual site conditions rather than treating the listed times as guaranteed.
The source’s insulation description is not a quantified thermal specification. Obtain supporting performance evidence before making numerical thermal or energy-saving claims.
Consult the current safety data sheet for handling, PPE, cleaning, storage and disposal.
Evidence reviewed 19 October 2026. Each reference below identifies its role and scope. Logos identify the source or organisation; they do not by themselves establish approval of this product, ECOPROCORK or a complete installation.
Manufacturer management systems. Decoproyec displays this RINA mark for ISO 9001 and ISO 14001, together with CISQ and IQNet references. These relate to the manufacturer’s management systems, rather than a performance certification for this individual product.
The current certificate numbers, editions, scope and expiry dates were not supplied on the technical page checked. View manufacturer source.
Product test references: The source names UNE-EN ISO 2811-1, UNE-EN ISO 3251, UNE-EN ISO 3233-3 and UNE 48301. These are test-method references; the source does not identify the performing laboratory or certificate numbers.
Documents for specification: Request the current product declaration, applicable certificates and full test reports, including report numbers, issue dates, grade, substrate, thickness and expiry where relevant. Ask ECOPROCORK for supporting technical documents.
Document access reviewed 19 October 2026. These are the supplied manufacturer documents. Their printed dates are shown where available; this review does not establish that they are the latest issue for the product currently supplied.
Safety documents and English summaries · Full technical document library
Document: EP-DECOCORK-THERMAL-CORK-PAINT · Web edition 1.2 · Updated 19 October 2026.
The PDF is generated on request from this published page, including the current technical matrix and product image. Update the edition and revision date when changing the content.